技术文章
人叉头框C2(FOXC2)elisa试剂盒2022年价格
阅读次数:1632次 发布时间:2022/11/16 16:58:19
使用说明书
检测原理
试剂盒采用双抗体夹心法酶联免疫吸附试验(ELISA)。往预先包被人叉头框C2(FOXC2)捕获抗体的包被微孔中,依次加入标本、标准品、HRP标记的检测抗体,经过温育并彻di洗涤。用底物TMB显色,TMB在过氧化物酶的催化下转化成蓝色,并在酸的作用下转化成*终的黄色。颜色的深浅和样品中的人叉头框C2(FOXC2)呈正相关。用酶标仪在450nm 波长下测定吸光度(OD 值),计算样品浓度。
试剂盒组成
名称 | 96孔配置 | 48孔配置 | 备注 |
微孔酶标板 | 12孔×8条 | 12孔×4条 | 无 |
标准品 | 0.3mL | 0.3mL | 无 |
样本稀释液 | 6mL | 3mL | 无 |
检测抗体-HRP | 10mL | 5mL | 无 |
20×洗涤缓冲液 | 25mL | 15mL | 按说明书进行稀释 |
底物A | 6mL | 3mL | 无 |
底物B | 6mL | 3mL | 无 |
终止液 | 6mL | 3mL | 无 |
封板膜 | 2张 | 2张 | 无 |
说明书 | 1份 | 1份 | 无 |
自封袋 | 1个 | 1个 | 无 |
注:标准品浓度依次为:1200、600、300、150、75、0 pg/mL.
试剂的准备
20×洗涤缓冲液的稀释:蒸馏水按1:20稀释,即1份的20×洗涤缓冲液加19份的蒸馏水。
Human FOXC2 (FOXC2) ELISA Kit instruction
Intended use
This FOXC2 ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures. The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of FOXC2 in the sample, this FOXC2 ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus FOXC2 concentration. The concentration of FOXC2 in the samples is then determined by comparing the O.D. of the samples to the standard curve.
Materials supplied
Name | 96 determinations | 48 determinations |
Microelisa stripplate | 12*8strips | 12*4strips |
Standard | 0.3ml | 0.3ml |
Sample diluent | 6.0ml | 3.0ml |
HRP-Conjugate reagent | 10.0ml | 5.0ml |
20X Wash solution | 25ml | 15ml |
Chromogen Solution A | 6.0ml | 3.0ml |
Chromogen Solution B | 6.0ml | 3.0ml |
Stop Solution | 6.0ml | 3.0ml |
Closure plate membrane | 2 | 2 |
User manual | 1 | 1 |
Sealed bags | 1 | 1 |
Note: Standard concentration was followed by:
1200、600、300、150、75、0 pg/mL.
Reagent preparation
20×wash solution:Dilute with Distilled or deionized water 1:20.
Assay procedure
1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.
2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.
3. Add Sample: Add testing sample 10μl Then add sample diluent 40μl to testing sample well; Blank well doesn’t add anyting.
4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C.
5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.
6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.
7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not
appear uniform, gently tap the plate to ensure thorough mixing.
8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.
原创作者:上海极威生物科技有限公司
联系人:陈经理(在阿仪网上看到的)
电 话:15214379366
手 机:16602115336
Q Q:435399850
传 真:021-80186165
邮 箱:435399850@qq.com
地 址:上海市崇明县长兴镇潘园公路1800号2号楼9703室